Menu
Support
Technical library

Technical library

The Megger technical library provides access to a range of additional content and resources such as technical guides, application notes and more. Use the filters to browse specific content (e.g. application notes) or refine your search to a particular electrical application area. 

 

If you would like to see the content we have available on a particular subject or need to locate some software, simply enter a search below. Please note, you will need to create an account to access some resources.

Filter by application type:
    Showing item(s) 1 - 10 of 15 in total
Application for testing Self-powered relays SEG (Woodward) WIP1 and WIC1
Self-Powered-Relay (SPR) takes its supply from the CT-s connected and also the energy for tripping the breaker. SPR either have special CT made for the relay or are made to be used directly with standard CT-s.
Published: 28 October 2020
Download PDF
Testing self-powered relays with SVERKER900
 Self-powered relays will be animportant component for the protection of the smart grid.While they allow reducingthe cost of the protection system, they are definitely a challenge for relay test sets, that are required to provide the voltage and current signals to simulate the power system fault, but also the generatedsignals need to have necessary electric power to supply the protection relay.SVERKER 900 is designed to manage this task and this Technical Guide describes how two self-powered relays can be tested.This document guides through the testing of two self-powered overcurrent relaysfrom SEG GmbH (formerly Woodward), WIC-1 and WIP-1, with the relay test set SVERKER 900, for commissioning/maintenance purposes.The Technical Guide details on the principles adopted in the testing with reference to relevant IEC standards and to the relay manuals. In addition,basic instructions on the correct usage of the testing possibilities offered by SVERKER 900are described
Published: 16 October 2020
Download PDF
Guide to Low Voltage Motor Testing
Guide to Low Voltage Motor Testing
Published: 3 October 2019
Download PDF
Getting Down To Earth - A practical guide to earth resistance testing
Earth testing and resistivity measuring requires sensitive equipment and sophisticated calculations. This guide makes these processes easier to understand for both large and small ground systems, with detailed studies of various relevant testing methods.
Published: 22 May 2019
Download PDF
A Guide to Transformer Ratio Measurements
Transformers are subject to mechanical impact and vibration. Problems or faults occur due to poor design, assembly, handling, poor environments, overloading or poor maintenance. Measuring the polarity and turn ratio of a transformer winding assures that the connections are correct and there are no severe mismatches or opens. Many transformers have taps built into them. These taps allow the ratio to be increased or decreased by fractions of a percent. If any of the ratio changes involve a mechanical movement of a contact from one position to another, these tap changes should also be checked during a ratio test.
Published: 24 January 2019
Download PDF
A guide to power quality testing
A comprehensive guide to testing power quality.
Published: 7 March 2018
Download PDF
A Stitch in time
A complete guide to electrical insulation testing
Published: 19 June 2017
Download PDF
Pocket guide to PAT testing
this pocket guide we have endeavoured to cover the details of the 4th Edition - rather than clarify the changes – in an easy-to-read manner.
Published: 9 March 2017
Download PDF
The Megger guide to insulating oil dielectric breakdown testing
Gain insight into the different types of oil testing methods, including oil dielectric breakdown testing moisture content testing. This guide covers best practices for oil testing, the correct equipment to use, and the different IEEE/IEC standards to adhere to when testing.
Published: 21 February 2017
Download PDF
Guide to insulation testing above 1kV
This guide discusses the causes of insulation degradation on >1kV power cables, and the process of measuring degradation before a fault can develop. The guide also recommends the best equipment to use with reference to IEEE standards.
Published: 21 February 2017
Download PDF
  • 1
  • 2
  • >
  • Showing item(s) 1 - 10 of 15 in total